|
Pulmor Enclosed Cargo Box Trailer & Cover; Lightweight cargo box trailer for road trips, sports and outdoor recreation. Pulmor cargo trailers are made in the USA. The cargo box body and lid are made of robust polyethylene which will not dent, rust or rot. The color pigment is in the polyethylene (not painted on).
Pulmor Cargo Trailer - Standard Features & Benefits
- LIGHTWEIGHT + STREAMLINED + LOW PROFILE = FUEL EFFICIENT
- Small trailer body is easy to tow and maneuver. You can see over the top of the trailer through the rear view mirror in most vehicles.
- Cargo Box Color Options: RED, YELLOW, BLACK, DARK GRAY, DARK GREEN. Lid is only available in LT GRAY. Color is in the molded material. (Note that sunlight and weather will fade ANY colored surface over time. To preserve the finish and depth of color, keep the trailer out of direct sunlight or cover it with a tarp when not in use for long periods of time. Covering the trailer for long term storage will also greatly extend the life of the tires, rubber components and lubrication.)
- Floor is molded as part of trailer shell and has a removable drain plug.
- Water tight polyethylene box and raised rib, removable lid keeps cargo dry. The lockable lid removes from the inside for safety and security.
- Aluminum support pole and indents inside of lid to hold cargo lid open.
- Standard 12" White Steel Spoke Wheels with 4.80 x 12B Highway Rated Tires.
- Torsion Axle (no leaf springs required)
- Bearing Size: 1-1/16" Inner and Outer
- EZ LUBE HUBS allow repacking of wheel bearings without removing them.
- Class 2 Coupler with Safety Chains
- Heavy-Duty Fully Welded 3" x 2" Tubular Steel Frame
- Lighting complies with all MOT and DOT requirements.
- Pre-Wired with Standard 4-Wire Flat Connector. Wiring harness fits inside the tongue.
- Removable Tongue
- Hitch Height is 19" to the top of the ball when secured to tow vehicle.
- Fenders - Round, Bolt-On Roto Molded Polyethylene (same material as cargo box)
- Interior Volume 32.5 cubic ft.
- Easy Assembly With Common Hand Tools - View Assembly Instructions
- 1-Year Limited Manufacturer's Warranty
| EZ Lube Hubs channel new grease to the wheel bearings from the grease fitting at the end. Both inner and outer bearings can be re-greased without removing the hub. |
 |
 |
The CLASS II torsion axle flexes to absorb the up and down motion caused by bumps and dips in the road. Rubber cushions between the axle and hub mounting plate absorb shock.
The torsion axle provides for a smooth ride and eliminates the need for leaf springs, which lowers the height of the trailer bed and enables easier loading and unloading of cargo. |
Accessories for Pulmor Cargo Box Trailers
Important! If you are ordering a Pulmor trailer, select an upgrade package in the pop-up instead of adding a rack, spare wheel/tire or jack stand as a separate product. The freight charge for the Pulmor trailer kit is flat-rate and all of the accessories can be included on one pallet. When accessories are ordered separately they are treated by the shopping cart as separately packaged items, which typically cost more to deliver.
Pulmor Aluminum Cargo Carrier Rack
 |
| 4.80 x 12" Wheel/tire |
Part No:TW480x12B5 |
$
97.00 + Shipping |
| 5-Holes, Capacity: 780 lbs. |
Shipping Wt.: 22 lbs. |
|
| Steel spoke wheel with white powder coat paint. Fits Pulmor and Yuppie trailers |
|
 |
| Spare Tire U-bolt Bracket |
Part No: TS67C |
$
19.00 + Shipping |
| Fits 12" 5-hole wheels |
Shipping Wt.: 1 lb. |
|
Fits over U-channel or square steel tubing to fasten spare tire on the tongue. Use with models: 745TC, 861TC, 749TC, Pulmor and Yuppie.
|
|
 |
| Clamp-on Wheel Jack |
Part No: WJ1 |
$
55.00 + Shipping |
| |
Shipping Wt.: 1 lb. |
|
Fits over U-channel or square steel tubing to fasten spare tire on the tongue. Use with models: 745TC, 861TC, 749TC, Pulmor and Yuppie.
|
|
|
